QuickLabel Systems QLS-4100X Guide d'installation télécharger pdf (Page 16)

QLS-4100 X 16

Installing the Unwind Mandrel

Your QLS-4100 X was shipped with the Media Unwind Mandrel uninstalled to

protect it from damage during transit. The mandrel is easily installed by following

the procedure outlined below.

Tools Needed

1/8” Allen Wrench

Slide the media unwind mandrel onto the shaft until the backplate flange is seated

firmly against the collar located on the inside of the shaft. The outside of the shaft

should be flush with the surface of the mandrel.

Firmly tighten the supplied Allen set screw against the shaft.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 117 118

Operation & Setup Guide 1
Table of Contents 3
1 Quick Start 7
QuickLabel Systems Media 8
Quick Start Guide 9
2 Physical Setup 10
Unpacking the Printer 11
Printer Orientation 12
Features of the QLS-4100 X 13
Side View 14
Rear Panel View 15
Installing the Unwind Mandrel 16
Power Connection 17
Computer Connections 18
Centronics Parallel Port 19
RS-232 Serial Port 20
Network Connection 21
Utility Port Connection 22
Compressed Air Connection 23
DIP Switch Settings 24
3 Loading Media and 26
Calibration 26
Loading Label or Tag Media 29
Adjusting the Media Sensor 32
Calibrating Media 33
Pause: Gap 35
Calibration Bad 35
4 Keypad Controls 39
and Menus 39
Keypad Layout and Functions 40
Deletes all labels 41
SELECT to confirm 41
Menu Functions 42
Print Speed 43
Pause: Speed 43
Speed = 4 in/s * 43
Print Intensity 44
Pause: Intensity 45
Head 1 = 12 * 45
Print Offset 46
Pause: Print Offset 46
Offset = 0 * 46
Windows Print Mode 48
Ready: Windows Print 48
Repeat 10 Label(s) 48
Mirror Mode 49
Pause: Mirror Mode 49
Cutter Flag 50
Pause: Cutter 50
Flag Off * 50
Cutter Offset 51
Offset = 0 * 51
Print Line Adjustment 52
Pause: Test Print 52
Proc. Block Pattern (CMYK) * 52
Pause: Print Line Adj 53
Head 1 = -4 * 53
Cross Web Adjustment 54
Pause: Cross Web Adj 55
Head 1 = < 5 * 55
TTR Sensor 56
Pause: TTR Sensor 56
Enabled * 56
Calibrate 57
Test Print 58
Test Pattern: 1 in * 58
Factory Reset 59
Pause: Factory Reset 59
Press SELECT 59
Resets all settings 59
QLS Settings 61
Pause: QLS Settings 61
SELECT to print 61
System Baseline 62
Pause: Sys Baseline 62
Baseline = +3 * 62
TTR / Media 63
Pause: TTR/Media 63
Standard * 63
TTR Drop 64
Pause: TTR Drop 64
Head 1 = 22 * 64
5 Operation 65
Printing with the QLS-4100 X 66
RUN with NO AIR ? 67
Press: Select 67
Printer Indicators 68
Error Messages 69
Format Error 70
Head x up 70
SELECT to disable 70
Head x Disabled 70
Drive Roll Up 70
Printheads Disabled 71
Hd1 Hd2 Hd3 Hd4 71
Color Alignment 72
Evaluating print quality 77
Advancing the Media 78
Adjusting the Print Speed 79
Printing Labels 81
Printing Test Patterns 82
6 Advanced 83
Adjustments 83
Printhead Tangency Alignment 84
Tools Needed 85
Printhead Lift 87
Adjusting System Baseline 88
7 Maintenance 89
and Repair 89
Recommended Tool List 90
Routine Cleaning 91
Printhead Replacement 92
Platen Replacement 94
Drive Roll Replacement 95
Pinch Roller Replacement 96
Firmware Upgrades 98
Appendix A 99
Physical Data 99
QLS-4100 X Dimensions 100
Appendix B 102
Specifications 102
QLS-4100 X Specifications 103
Appendix C 104
Replacement Parts 104
Color QuickLabel 99 Pro 106
Appendix D 106
Color QuickLabel 99 Pro Setup 107
Appendix E 111
Windows Printer Driver 111
Windows Printer Driver Setup 112

Commentaires sur ces manuels

Pas de commentaire

QuickLabel Systems QLS-4100X Guide d'installation Page 16

Commentaires sur ces manuels